CALCIUM CHLORATE, AQUEOUS SOLUTION
| UN 编号 | UN2429 |
|---|---|
| 中文名称 | 氯酸钙,水溶液 |
| 英文名称 | CALCIUM CHLORATE, AQUEOUS SOLUTION |
| 危险类别 | 第5.1类 |
| 包装类别 | II |
| 海洋污染物 | 否 |
| 有限数量 | 1 L |
| 例外数量 | E2 |
| EmS 应急措施 | F-H,S-Q(F-H, S-Q) |
| 包装类别 | 类别 | 有限数量 | 例外数量 | 包装导则 | 罐柜导则 |
|---|---|---|---|---|---|
| II | 5.1 | 1 L | E2 | P504 | T4 |
| III | 5.1 | 5 L | E1 | P504 | T4 |
无色液体,遇火时,可引起爆 炸。泄漏和随后的水蒸发可增 加下列危险性:1.与可燃物(特 别是纤维材料如黄麻。棉花和 剑麻)或硫磺接触有自燃的危 险。2.与铵化合物、金属粉末 或油接触有爆炸危险。
Colourless liquid. When involved in a fire, may cause an explosion. Leakage and subsequent evaporation of the water may present increased dangers as follows: .1 in contact with combustible material (particularly with fibrous material such as jute, cotton or sisal) or sulphur, danger of spontaneous combustion; .2 in contact with ammonium compounds, powdered metals or oils, danger of explosion.
出处:IMDG Code 42-24 第 683 页
本条目适用的包装导则: P504 ;有限数量 1 L,例外数量 E2。
P504 只要符合第4.1.1和4.1.3节的一般规定,允许使用下列包装: 组合包装最大净重 (1) 外包装:(1A1、1A2、1B1、1B2、1N1、1N2、1H1、1H2、1D、 75kg 1G、4A、4B、4N、4C1、4C2、4D、4F、4G、4H2) 内包装:最大容积为5L的玻璃容器。 (2) 外包装 :(1A1、1A2、1B1、1B2、1N1、N2、1H1、1H2、1D、 75kg 1G、4A、4B、4N、4C1、4C2、4D、4F、4G、4H2)。 内包装:最大容积为30L的塑料容器。 (3) 最大容积为40L的金属容器装于1G、4F或4G的外包装中。 125kg (4) 最大容积为 40L 的金属容器装于(1A1、1A2、1B2、1N1、1N2、 225kg 1H1、1H2、1D、4A、4B、4N、4C1、4C2、4D、4H2) 外包装中。 单一包装最大容积桶钢,不可拆卸桶顶(1A1) 250L 铝,不可拆卸桶顶(1B1) 250L 其它金属,不可拆卸桶顶(1N1) 250L 塑料,不可拆卸桶顶(1H1) 250L 罐钢,不可拆卸罐顶(3A1) 60L 铝,不可拆卸罐顶(3B1) 60L 塑料,不可拆卸罐顶(3H1) 60L 复合包装装于钢桶或铝桶中的塑料容器(6HA1、6HB1) 250L 装于纤维质、塑料或胶合板桶中的塑料容器(6HG1、6HH1、6HD1) 120L 装于钢或铝板条箱或箱内的塑料容器或装于木质、胶合板、纤维板或硬塑 60L 料箱内的塑料容器(6HA2、6HB2、6HC、6HD2、6HG2、6HH2,) 装于钢、铝、纤维质或胶合板桶内的玻璃容器(6PA1、6PB1、6PD1 或 60L 6PG1),或装于钢、铝、木质或纤维板箱内或藤条筐内的玻璃容器 (6PA2、6PB2、6PC、6PG2 或 6PD2),或装于硬质或泡沫塑料容器内的玻璃容器(6PH1或6PH2)。 特殊包装规定: PP10 对于UN 2014和3149,包装须有通风孔。 P504 PP31 对于UN 2626,包装须密封。
P504 The following packagings are authorized, provided that the general provisions of 4.1.1 and 4.1.3 are met. Combination packagings Maximum net mass (1) Outer packagings: (1A1, 1A2, 1B1, 1B2, 1N1, 1N2, 1H1, 1H2, 1D, 1G, 4A, 4B, 4N, 4C1, 75 kg 4C2, 4D, 4F, 4G, 4H2) Inner packagings: Glass receptacles with a maximum capacity of 5 L (2) Outer packagings: (1A1, 1A2, 1B1, 1B2, 1N1, 1N2, 1H1, 1H2, 1D, 1G, 4A, 4B, 4N, 4C1, 75 kg 4C2, 4D, 4F, 4G, 4H2) Inner packagings: Plastics receptacles with a maximum capacity of 30 L (3) Outer packagings: (1G, 4F or 4G) 125 kg Inner packagings: Metal receptacles with a maximum capacity of 40 L (4) Outer packagings: (1A1, 1A2, 1B1, 1B2, 1N1, 1N2, 1H1, 1H2, 1D, 4A, 4B, 4N, 4C1, 4C2, 4D, 225 kg 4H2) Inner packagings: Metal receptacles with a maximum capacity of 40 L Single packagings Maximum capacity Drums steel, non-removable head (1A1) 250 L aluminium, non-removable head (1B1) 250 L metal, other than steel or aluminium, non-removable head (1N1) 250 L plastics, non-removable head (1H1) 250 L Jerricans steel, non-removable head (3A1) 60 L aluminium, non-removable head (3B1) 60 L plastics, non-removable head (3H1) 60 L Composite packagings Plastics receptacle in steel or aluminium drum (6HA1, 6HB1) 250 L Plastics receptacle in fibre, plastics or plywood drum (6HG1, 6HH1, 6HD1) 120 L Plastics receptacle in steel or aluminium crate or box or plastics receptacle in wood, 60 L plywood, fibreboard or solid plastics box (6HA2, 6HB2, 6HC, 6HD2, 6HG2 or 6HH2) Glass receptacle in steel, aluminium, fibre or plywood drum (6PA1, 6PB1, 6PD1 or 6PG1) 60 L or in a steel, aluminium, wood or fibreboard box or in wickerwork hamper (6PA2, 6PB2, 6PC, 6PG2 or 6PD2) or in expanded or solid plastics packaging (6PH1 or 6PH2) Special packing provisions: PP10 For UN Nos. 2014 and 3149, the packaging shall be vented. PP31 For UN 2626, packagings shall be hermetically sealed.
出处:IMDG Code 42-24 第 214 页(4.1.4.1)
IBC02 只要符合第4.1.1、4.1.2和4.1.3节的一般规定,允许使用下列IBCs: 金属(31A、31B和31N); 硬质塑料(31H1和31H2); 复合包装(31HZ1)。 特殊包装规定: B5 对于盛装UN 1791、2014、2984和3149的IBCs,须配备允许在运输过程中排气的装置。排气装置的入口须设在运输过程中IBC最大充装条件下的蒸气空间内。 B8 纯物质不得使用 IBCs 运输,因为已知该物质在 50°C蒸汽压超过 110kPa,在 55°C时蒸气压超过130kPa。 B15 对于硝酸含量超过 55%的UN 2031,硬质塑料 IBCs和复合IBCs的硬质塑料内容器的允许使用期限为生产日期起两年。 B16 对于UN3375,未经主管当局批准,不得使用31A和31N型的IBCs。 B20 对于包装类II的UN 1716、1717、1736、1737、1738、1742、1743、1755、1764、 1768、1776、1778、1782、1789、1790、1796、1826、1830、1832、2031、 2308、2353、2513、2584、2796和2817,IBCs须安装两个关闭装置。
IBC02 The following IBCs are authorized, provided the general provisions of 4.1.1, 4.1.2 and 4.1.3 are met: Metal (31A, 31B and 31N); Rigid plastics (31H1 and 31H2); Composite (31HZ1). Special packing provisions: B5 For UN Nos. 1791, 2014, 2984 and 3149, IBCs shall be provided with a device to allow venting during transport. The inlet to the venting device shall be sited in the vapour space of the IBC under maximum filling conditions during transport. B8 The pure form of this substance shall not be transported in IBCs since it is known to have a vapour pressure of more than 110 kPa at 50C or 130 kPa at 55C. ° ° B15 For UN 2031 with more than 55% nitric acid, the permitted use of rigid plastics IBCs and of rigid plastics inner receptacles of composite IBCs shall be two years from their date of manufacture. B16 For UN 3375, IBCs of type 31A and 31N are not allowed without competent authority approval. B20 For UN Nos. 1716, 1717, 1736, 1737, 1738, 1742, 1743, 1755, 1764, 1768, 1776, 1778, 1782, 1789, 1790, 1796, 1826, 1830, 1832, 2031, 2308, 2353, 2513, 2584, 2796 and 2817 coming under PG II, IBCs shall be fitted with two shut-off devices.
T1-T22 本可移动罐柜导则适用于第1类和第3至9类液体和固体物质,须满足第4.2.1节的一般规定和第6.7.2节的要求。带 FRP 外壳的可移动罐柜导则适用于第 1、3、5.1、6.1、6.2、8 和 9 类或小类物质。此外,第 6.10 章的规定适用于带 FRP 外壳的可移动罐柜。 最小罐壳厚度底部开口最低试验 (单位: mm-标准安全减压规定a 规定b 可移动罐柜导则压力钢) (见第6.7.2.8 (见第6.7.2.6 (bar) (见第6.7.2.4 条) 条) 条) 2.65 见6.7.2.4.2 正常见6.7.2.6.3
S T1 – T22 These portable tank instructions apply to liquid and solid substances of class 1 and classes 3 to 9. The general provisions of section 4.2.1 and the requirements of section 6.7.2 shall be met. The instructions for portable tanks with FRP shells apply to substances of classes or divisions 1, 3, 5.1, 6.1, 6.2, 8 and 9. Additionally, the provisions of chapter 6.10 apply to the portable tanks with FRP shells. Minimum shell thickness Pressure relief Bottom opening (in mm – reference provisionsa provisionsb instruction pressure (bar) steel) (see 6.7.2.8) (see 6.7.2.6) (see 6.7.2.4) 2.65 See 6.7.2.4.2 Normal See 6.7.2.6.3
不得超过第4.2.1.9.条中规定的充灌度。
The degree of filling prescribed in 4.2.1.9.2 shall not be exceeded.
本货物包件应张贴以下标签与标记:
5.1本 UN 可按有限数量运输(一览表额度 1L);若本票按限量运输,须加贴 LQ 标记并符合第 3.4 章要求
本 UN 可按例外数量运输(代码 E2);若本票按例外数量运输,须加贴 EQ 标记并符合第 3.5 章要求
本条目适用特殊规定: 223。
如果在测试时物质所表现的化学或物理特性不满足第3栏中所列类别或任何其他类别已建立的定义标准,除了2.10.3适用的海洋污染物以外,则不适用本《规则》的规定。
If the chemical or physical properties of a substance covered by this description are such that, when tested, it does not meet the established defining criteria for the class or division listed in column 3, or any other class or division, it is not subject to the provisions of this Code except in the case of a marine pollutant where 2.10.3 applies.
出处:IMDG Code 42-24 第 770 页
| 积载与操作 | 积载类B(Category B) |
|---|---|
| 隔离 | SGG4 SG38 SG49 SG62 |
4 氯酸盐类
4 chlorates
与SGG2 - 铵化合物“隔离”。
Stow “separated from” SGG2 – ammonium compounds.
与SGG8 - 氰化物“隔离”。
Stow “separated from” SGG6 – cyanides.
与硫“隔离”。
Stow “separated from” sulphur. Segregation Description code
出口危险货物包装使用鉴定结果单(危包证)的办理逻辑,以及它和船级社证、钢瓶证、SOC 罐证分别在什么场景下用、向谁申请。
DG 申请表(DGD)被船公司退回,十有八九是这十个问题。逐条列出错误表现、船司退回话术和正确填法。
按 UN2429 自动带出类别、包装组、隔离要求与危包证清单,省掉翻书对表的时间。
生成 DG 申报资料 →